Sharelaser,  CEO@sharelaser.com  SHARE LASER, Laser marking machine, laser welding machine, laser cleaning machine

Precautions:

1. Check whether the red light is in the center before turning on. If it is not in the center, if you are forcibly welded, will burn the copper nozzle and the focus mirror.

2. Change the distilled water every month and blow off the dust with air guns.

3. When changing the protective lens, the gun head should be facing down. Do not let the dust enter. If there is dust, it will burn the lens. 

4. The welding gun cannot be welded vertically, and it will be easy to burn the lens, and it takes about 60 degrees to weld.

5. The video sent to you should be watched at least once, precautions, write on your own book, and write to deepen the impression again.

6. Let the customers learn to use the welding function, and then use other cutting and cleaning functions.

7. When using the cleaning function, it is best not to change the focusing mirror. If there is dust, burn the gun, this is human damage and not within the warranty range. Change the lens, in principle, it can only be changed in the dust -free workshop. For beginners, the focusing mirror is taboo.

8. For the first time, you can use tap water to test, but after distilled water arrives, you must replace it in time. The tap water pipe is over time, and there will be stains in the tube. The water pipe of the laser and gun is as detailed, and it will be blocked after a long time.

9. Wait for the water temperature to about 26 ° C, then press Enable. When the water temperature reaches about 26 degrees, the laser will not report the alarm. Then press ENABLE, which is equivalent to giving the signal to the touch screen and control box. Then press the gun button, the clip to the workpiece, you can shoot the laser. If you do not clip the workpiece, there will be no laser, and the clip and the buttons on the gun must be connected at the same time to come out to the laser. If don't clip a clip, and shoot a laser, which is very dangerous. The clips are generally clamped on the workpiece, not on the metal scale tube of the gun.

10. In addition, the electricity connected cannot be shared with other large equipment, and there will be interference. There must be no equipment such as arc welding around, and there will be interference.

11. It is necessary to blow the protective gas, like Nitrogeon or Argon. If you don't blow the gas, will directly burn the protective lens.

12. During the welding process, if the energy is found to be smaller, it is estimated that it is a black spot to protect the lens, and it should be replaced in time. If forcibly welding, the focus will be burned and the reflector will be burned. Therefore, it is necessary to check the protective lens and focusing mirror in time to avoid affecting other lenses.

13. Every time you welded, check whether the red light is located at the center of the nozzle, because when the gun is placed on the workbench, the red light will be offset after the number of times. In particular, some masters do not care about welding guns and throw them directly on the workbench.

14. When clamp is clamped on the metal sheet, sometimes welding and sometimes power get weak, it means that the conductivity is not good. The solution is that the clamp is clamped on the welding gun, and the conductivity will be better. 

Cutting function:

Set the scan width to 0, the scanning speed becomes 0, the power setting is 1200, the duty cycle is 100%, the frequency is 2000Hz. The cut parameters are set.

Remove the wire stent and the wire delivery tube, and replace the copper nozzle with a cut nozzle.

Before cutting, check whether the red light is in the center. If it is not, take out the front small cut nozzle, adjust the red light center, and let the red light in the middle of the round halo light.

Cleaning function:

Click the system to switch icons in the upper right corner of the touch screen, and determine the restart system according to the prompts, and switch to the cleaning system. And to dismantle the components: wire feeder bracket, sending wire tube, scale tube, and copper nozzle.

Press the button on the gun continuously, press 2 times quickly, and then laser beam will come out. When cleaning, take a fan and blow the dust away. Try not to let the dust float near the gun.

The standard focus lens is F150mm, can clean 20mm width(Cleaning welding path function). When replace F400mm lens, can clean 40mm width(Cleaning rust function). But better not to replace focus lens, because if dust goes inside, it may break the welding head.